1.

Analysis of factors affecting delamination in drilling GFRP composite

صفحه 281-289
Sachin G Ghalme؛ Yogesh Bhalerao؛ Kamlesh Phapale

2.

Multi-objective particle swarm optimization of WEDM process parameters for inconel 825

صفحه 291-309
P. Kumar؛ M. Gupta؛ V. Kumar

3.

Mechanism of surface generation in grinding AA6061-TiB2/ZrB2 in-situ composite

صفحه 311-324
A. Mahamani؛ S. Jawahar؛ J. P. Davim

4.

Characteristics of fish oil biodiesel with the impact of diesel fuel addition on a CI engine

صفحه 325-336
Deepak Kumar Sharma؛ Tikendra Nath Verma

5.

Analysis of generalized compressor characteristics on surge phenomena in axial compressors

صفحه 337-344
Adnan Maqsood؛ Muhammad Kamran Khan Tareen؛ Rizwan Riaz؛ Laurent Dala

6.

Numerical analysis of microchannel based bio-inspired heat sinks with multiple inlet-outlet pairs for cooling square shaped circuits

صفحه 345-359
Kandassamy K؛ Prabu Balakrishnan

7.

Heat transfer characteristics of methane-air diffusion flames impinging normally on plane surfaces

صفحه 361-372
Satyananda Tripathy؛ Manmatha K Roul؛ Akshaya K Rout

8.

Numerical analysis of photovoltaic power generation in different locations of Bangladesh

صفحه 373-389
Rehena Nasrin Nasrin؛ M. Saddam Hossain

9.

Application of image-based acquisition techniques for additive manufacturing using canny edge detection

صفحه 391-404
Ahalya Ravendran؛ Suchada Rianmora

10.

Effect of geometrical parameters on fluid film coefficients in tilting pad journal bearing

صفحه 405-427
Harsh Kumar Dixit؛ T.C Gupta

11.

Thermo-mechanical characterization of post-consumer recycled high impact polystyrene from disposable cups: Influence of the number of processing cycles

صفحه 427-436
Hanan EL BHILAT؛ Khalid El Had؛ Houda SALMI؛ Abdelilah Hachim

12.

Simulation of blood flow in the abdominal aorta considering penetration into the organs using pore network model

صفحه 437-447
Safoora Karimi؛ Mitra Dadvar؛ Bahram Dabir

13.

Analysis of chemical reaction and thermophoresis on MHD flow near the accelerated vertical plate in a rotating system with variable temperature

صفحه 449-460
mohammad shareef؛ mohammad shareef

14.

Numerical study of transient behavior and heat transfer in a phase change material affected by heat transfer fluid flow parameters

صفحه 461-471
Omid Ahmadi؛ Sahand Majidi؛ Pooyan Hashemi Tari

15.

Experimental evaluation and estimation of frictional behavior of polymer matrix composites

صفحه 473-483
Hiral Parikh؛ Piyush Gohil

16.

Novel numerical solution of non-linear heat transfer of nanofluid over a porous cylinder: Buongiorno-Forchheimer model

صفحه 485-496
Vasu B؛ Atul Kumar Ray

17.

Linear thermal radiation effects on MHD viscoelastic fluid flow through porous moving plate with first order chemical reaction, variable temperature, and concentration

صفحه 497-509
shaik ibrahim؛ k suneetha؛ P Vijaya Kumar؛ Kanithi Jyothsna

18.

Investigation of temperature jump and slip effects on nanofluid treatment inside a vertical annulus via modified Buongiorno’s model

صفحه 511-524
Hamidreza Ghaffarianjam؛ Sajad A. Moshizi؛ Mahdi Zamani؛ Mahdi Amiri Daluee

19.

Effect of axial groove location, length, and width ratio on bearing properties and stability

صفحه 525-537
Vijay Kumar Dwivedi؛ Pooja Pathak

20.

Investigation of natural convection heat transfer of MHD hybrid nanofluid in a triangular enclosure

صفحه 539-549
Ali Akbar rashidi؛ Ehsan Kianpour


سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب