تعداد نشریات | 13 |
تعداد شمارهها | 206 |
تعداد مقالات | 2,049 |
تعداد مشاهده مقاله | 2,721,220 |
تعداد دریافت فایل اصل مقاله | 1,972,880 |
Optimal Design of Axial Flux Permanent Magnet Synchronous Motor for Electric Vehicle Applications Using GAand FEM | ||
Journal of Electrical and Computer Engineering Innovations (JECEI) | ||
مقاله 3، دوره 3، شماره 2 - شماره پیاپی 6، مهر 2015، صفحه 89-97 اصل مقاله (790.76 K) | ||
نوع مقاله: Original Research Paper | ||
شناسه دیجیتال (DOI): 10.22061/jecei.2016.401 | ||
نویسندگان | ||
M. Ahmadi Darmani؛ H. Hooshyar | ||
Islamic Azad University, Science and Research Branch | ||
تاریخ دریافت: 17 آبان 1394، تاریخ بازنگری: 13 بهمن 1394، تاریخ پذیرش: 13 بهمن 1394 | ||
چکیده | ||
Axial Flux Permanent Magnet (AFPM) machines are attractive candidates for Electric Vehicles (EVs) applications due to their axial compact structure, high efficiency, high power and torque density. This paper presents general design characteristics of AFPM machines. Moreover, torque density of the machine which is selected as main objective function, is enhanced by using Genetic Algorithm (GA) and variation of PM characteristics, based on sizing equation and Finite Element Analysis (FEA). Then, torque ripple of the motor is reduced according to the effect of PM characteristics on Torque Ripple Factor (TRF). The designed machine produces sinusoidal back-EMF waveform. The torque density is improved and the torque ripple is reduced. The results are validated by using 3D-FEA (FEA) . Furthermore, to assess the obtained results by FEA method, an advanced vehicle simulator (ADVISOR) software is used to demonstrate the performance improvement over the Europe test drive cycles. | ||
کلیدواژهها | ||
Axial Flux Permanent Magnet؛ Motor؛ Finite Element Analysis (FEA)؛ Genetic Algorithm (GA)؛ Torque Ripple Analysis (TRF)؛ Electric Vehicles (EVs) | ||
مراجع | ||
[1] M. J. Yang, H. L. Jhou, B. Y. Ma, K. Kai Shyu,”A Cost-Effective Method of Electric Brake With Energy Regeneration for Electric Vehicle” IEEE Trans. Ind. Electron.,vol. 56, no. 6, pp. 2203-2212, June. 2009.
[2] G. Nanda, N. C. Kar, ”A Survey And Comparison Of Characteristics Of Motor Drives Used In Electric Vehicles” IEEE Electrical and Computer Engineering Conf, pp. 811-814.
[3] S. Onoda, A. Emadi,”PSIM-Based Modeling of Automotive Power Systems Conventional, Electric, and Hybrid Electric Vehicle” IEEE Trans.Vehicular Technology, vol. 53, no. 2, pp. 390-400, Mar. 2004.
[4] Aydin, M., S. Huang, T.A. Lipo, “Axial Flux Permanent Magnet Disc Machines: A Review” Research Report,2004-2010. [5] S. AsgharGholamian, M.T. AbbasiAblouie, A. Mohseni and S. EsmaeiliJafarabadi, “Effect of Air Gap on Torque Density for Double-Sided Axial Flux Slotted Permanent Magnet Motors using Analytic and FEM Evaluation”, Journal of Applied Sciences Research, 5(9): 1230-1238, 2009.
[6] J. Gieras, Rong-Jiewang and J.Kamper, “Axial Flux Permanent Magnet Brushless Machines”, Publisher:Springer,2005. [7] D.C. Hanselman, “Brushless Permanent-magnet Motor Design”, Number 2, McGraw-Hill,Inc, 1994.
[8] Funda. Sahin,”Design and development of high speed axial-flux permanent magnet machines” Thesis, Doctor of Philosophy,Cip-Data ClibraryTechnischeUniversiteit Eindhoven,2001.
[9] Qu Ronghai, T.A. Lipo, “Analysis and modeling of air-gap and zigzag leakage fluxes in a surface-mounted permanentmagnet,” Machine IEEE Transactions on Industry Applications, Volume 40, Issue 1, pp 121-127, 2004
[10] Cirani M. &Lindstr¨om J. ”Electric hub wheel motors: An initial studyfor long haul applications” Technical report, Volvo 3P, 2009.
[11] Chiristian Du-Bar, “Design of an axial flux machine for an inwheel motor application” Master of science thesis, Department of Energy and Environment, Chalmers University Of Technology, 2011. | ||
آمار تعداد مشاهده مقاله: 2,290 تعداد دریافت فایل اصل مقاله: 4,112 |