Journal of Computational & Applied Research in Mechanical Engineering (JCARME)
مقاله 5 ، دوره 14، شماره 1 - شماره پیاپی 27 ، بهمن 2024، صفحه 63-76 867.37 K )
نوع مقاله: Review paper
شناسه دیجیتال (DOI): 10.22061/jcarme.2024.10785.2414 نویسندگان
Hasan Ghafourian Nosrati* 1 Mahdi Gerdooei 2 1 Department of Manufacturing Engineering, Esfarayen University of Technology, Esfarayen, North Khorasan, 966199819, Iran2 Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Semnan, 3619995161, Iran
تاریخ دریافت : 09 فروردین 1403 ،
تاریخ بازنگری : 23 تیر 1403 ،
تاریخ پذیرش : 03 مرداد 1403
چکیده In recent years, most industries such as the aerospace, automotive, and others have been pushed to methods for reducing costs. One of these methods is the rubber pad forming (RPF) process, which has been given more attention as a low-cost method than conventional methods. In RPF, unlike conventional methods which mainly use metals as tools, one of the tools will be made of elastic pads. The RPF process has attracted the attention of many researchers around the world. Researchers from Iran started their work in this field around 2001 and subsequently published several remarkable articles. The first published Iranian study of the RPF process dates back to 2003, indicating that the use of flexible tools has a history of two decades in Iran. However, in the last decade, the number of published Iranian articles in the RPF process field and the introduction of new methods based on RPF and its simulation has increased. This review article aims to outline Iran's involvement in the RPF process, and it emphasizes that Iranian researchers predominantly contribute to the RPF process through simulation, experimental endeavors, and the introduction of innovative methods utilizing flexible tools. کلیدواژهها
Rubber pad forming ؛ Simulation ؛ Sheet metal forming ؛ Tube bulging ؛ Elastomer
مراجع
[1] M. Ramezani and Z. M. Ripin, "Principles of rubber-pad forming", Rubber-Pad Forming Processes: Technology and Applications, 1st ed., Woodhead Publishing in Mechanical Engineering, Elsevier Science, pp. 23-42, (2012).
[2] R. Narimani, R. Maedolit and H. Rahravan, “Investigating the possibility of forming sheets metal in the rubber forming process”. Proc. of 6th Iranian Conf. "Manufacturing Engineering" , Tehran, Iran, (2004).
[3] M. Balcerzak, K. Żaba, M. Hojny, S. Puchlerska, Ł. Kuczek, T. Trzepieciński and V. Novák, “Experimental research and numerical modelling of the cold forming process of the inconel 625 alloy sheets using flexible punch”, Materials (Basel). , Vol. 17, No. 1, p. 85, (2023).
[4] N. Xiang, M. Yang, P. Wang, H. Wang, T. Huang, J. Guo and F.Chen, “Mechanism on the increased sheet metal formability in flexible-die forming process using elastic composites with magnetic-field-dependence as the pressure-carrying medium”, Int. J. Adv. Manuf. Technol. , Vol. 126, No. 1–2, pp. 17–34, (2023).
[5] Y. Shu, N. Xiang, H. Wang, M. Yang, P. Wang, T. Huang, J. Guo and F. Chen, “Numerical investigation of controllable non-uniform deformation of tailor-welded blanks using heterogeneous pressure-carrying medium”, Thin-Walled Struct. , Vol. 186, p. 110663, (2023).
[6] H. Wang, G. Chen, Q. Zhu, P. Zhang and C. Wang, “Frictional behavior of pure titanium thin sheet in stamping process: Experiments and modeling”, Tribol. Int. , Vol. 191, p. 109131, (2024).
[7] F. Bagheri, M. Sedighi and R. Maedolit, “Calculated the coefficients of hyperelastic materials in simulation of rubber pad forming processes”. Proc. of 12th Iranian Conf. "Manufacturing Engineering (ICME 2010)" , Tehran, Iran, (2011).
[8] F. Bagheri, M. Sedighi and R. Madoliat, “Investigation of the influence of flange length and die radius on spring-back of 135 bends by rubber pad forming”. Proc. of 5th Natl. Conf. of "Metals and Materials Formaing" , Tehran, Iran, (2011).
[9] A. Kami, “Experimental study of the deep drawing process of conical parts using rubber pads”. Proc. of 14th Iranian Conf. "Manufacturing Engineering" , Arak, Iran, (2017).
[10] M. Rezaei and K. Hasanpour, “Improving optical quality of poly methyl methacrylate sheet by forming with rubber”, J. Appl. Comput. Sci. Mech. , Vol. 29, No. 1, pp. 1–16, (2017).
[11] M. Mehrara and M. J. Nategh, “Analysis of continuous bending of thin plates in rubber pad bending”, Key Eng. Mater. , Vol. 473, pp. 145–150, (2011).
[12] M. Mehrara and M. J. Nategh, “Analytical-numerical solution of bending problem of thin plates in rubber pad bending”, Key Eng. Mater. , Vol. 473, pp. 190–197, (2011).
[13] M. Mehrara and M. J. Nategh, “Analysis of the elastic and plastic roll bending of sheet metal on a rubber pad”, Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. , Vol. 226, No. 4, pp. 722–732, (2012).
[14] B. Zareh, A. Vafaei-Sefat and V. Rikhtegar-Nezami, “Experimental and numerical investigatio of sheet metal forming using multi-point forming process”, Sci. J. Aerosp. Mech. , Vol. 8, No. 4, pp. 75–87, (2013).
[15] M. Elyasi, F. A. Khatir and M. Hosseinzadeh, “Lubricant effect on depth filling of metallic bipolar plates with concave and convex patterns in rubber pad forming process”, Modares Mech. Eng. , Vol. 15, No. 12, pp. 450–460, (2015).
[16] H. Talebi Ghadikolaee, M. Elyasi and M. Hosseinzadeh, “Investigate the effect of rubber layers thickness on forming of bipolar plate’s microchannels in rubber pad forming process”, Iran. J. Manuf. Eng. , Vol. 2, No. 4, pp. 57–69, (2016).
[17] M. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, “Investigation of dimensional accuracy of metallic bipolar plate’s micro channel in rubber pad forming process”, Modares Mech. Eng. , Vol. 15, No. 12, pp. 461–471, (2015).
[18] M. Elyasi, F. Ahmadi and M. Hosseinzadeh, “Experimental study of the die patterns in rubber pad forming process for production of metallic bipolar plates”, Modares Mech. Eng. , Vol. 15, No. 9, pp. 179–186, (2015).
[19] A. Niknejad, N. Rezaee and F. J. Asl, “Experimental investigation of Teflon-pad forming on circular metal blanks using a concave die”, J. Manuf. Process. , Vol. 20, pp. 282–290, (2015).
[20] M. Elyasi, F. A. Khatir and M. Hosseinzadeh, “Investigation of die clearance in rubber pad forming of metallic bipolar plates”, AUT J. Mech. Eng. , Vol. 1, No. 1, pp. 89–98, (2017).
[21] H. Talebi-Ghadikolaee, M. Elyasi and M. J. Mirnia, “Investigation of failure during rubber pad forming of metallic bipolar plates”, Thin-Walled Struct. , Vol. 150, p. 106671, (2020).
[22] M. Elyasi, F. A. Khatir and M. Hosseinzadeh, “Manufacturing metallic bipolar plate fuel cells through rubber pad forming process”, Int. J. Adv. Manuf. Technol. , Vol. 89, No. 9–12, pp. 3257–3269, (2017).
[23] A. Ansari, E. Shahrjerdi and E. Amini, “An experimental and numerical investigation of press force and weld line displacement of tailor welded blanks in conventional and rubber pad sheet metal forming”, Asian J. Eng. Technol. , Vol. 02, No. 04, (2012).
[24] H. T. Ghadikolaee, M. Elyasi, F. A. Khatir and M. Hosseinzadeh, “Experimental investigation of Fracture in rubber pad forming of bipolar plate’s micro channels”, Procedia Eng. , Vol. 207, pp. 1647–1652, (2017).
[25] M. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, “Fabrication of metallic bipolar plates in PEM fuel cell using semi-stamp rubber forming process”, Int. J. Adv. Manuf. Technol. , Vol. 92, No. 1–4, pp. 765–776, (2017).
[26] R. Kolahdooz, S. Asghari, S. Rashid-Nadimi and A. Amirfazli, “Integration of finite element analysis and design of experiment for the investigation of critical factors in rubber pad forming of metallic bipolar plates for PEM fuel cells”, Int. J. Hydrogen Energy , Vol. 42, No. 1, pp. 575–589, (2017).
[27] A. Mahshidifar and A. Vafaeesefat, “Numerical and experimental study of parameters affecting metal forming using rubber pads, on parts with radius of curvature”, Int. J. Adv. Des. Manuf. Technol. , Vol. 6, No. 1, pp. 9–17, (2013).
[28] S. Cinquemani, M. Sheykholeslami and S. Mazdak, “Numerical study of the of ultrasonic vibration in deep drawing process of circular sections with rubber die”, Vol. 1059539, p. 112, (2018).
[29] M. Borhani and F. Djavanroodi, “Rubber pad-constrained groove pressing process: Experimental and finite element investigation”, Mater. Sci. Eng. A , Vol. 546, pp. 1–7, (2012).
[30] A. Niknejad and I. Karami Fath, “Teflon-pad shaping process of circular metal blanks into quasi-cup specimens by theoretical and experimental methods”, Trans. Nonferrous Met. Soc. China (English Ed.) , Vol. 26, No. 1, pp. 213–227, (2016).
[31] H. G. Nosrati, M. Gerdooei and M. Falahati Naghibi, “Experimental and numerical study on formability in tube bulging: A comparison between hydroforming and rubber pad forming”, Mater. Manuf. Process. , Vol. 32, No. 12, pp. 1353–1359, (2017).
[32] H. G. Nosrati and M. Gerdooei, “Feasibility study of cam-shaped tube production using elastomeric tool versus fluid forming method”, Int. J. Adv. Manuf. Technol. , Vol. 95, No. 5–8, pp. 3029–3036, (2018).
[33] M. Darvishi Hoseini Ahangar, M. Sedighi and M. Khandaei, “Application of rubber pad forming process in local contraction of pipe for assembly in vehicle structure”, J. Mod. Process. Manuf. Prod. , Vol. 1, No. 3, pp. 71–77, (2010).
[34] H. G. Nosrati and M. Gerdooei, “Experimental and numerical study of friction in free bulging 304 stainless steel seamed tube using elastic pad”, Modares Mech. Eng. , Vol. 15, No. 4, pp. 30–40, (2015).
[35] H. G.Nosrati, S. M. H. Seyedkashi and M. Gerdooei, “Investigation of effective parameters in free bulging of stainless steel 304 tube using elastomer tool”, Modares Mech. Eng. , Vol. 16, No. 10, pp. 191–198, (2016).
[36] B. Abbaszadeh, H. Moslemi Naeini, J. Shahbazi Karimi, S. J. Hashemi and M. Nasrollahzade, “Experimental investigation of aluminum tube bulging using a rubber-pad on different loading curves”, Iran. J. Manuf. Eng. , Vol. 3, No. 2, pp. 62–69, (2016).
[37] S. Seddighi, M. M. Barzegari and H. Talebi-Ghadikolaee, “Numerical-experimental investigation of using rubber blank holder on wrinkling of metallic bipolar plates formed by stamping process”, Int. J. Hydrogen Energy , Vol. 48, No. 62, pp. 23967–23991, (2023).
[38] H. Talebi-Ghadikolaee, M. Elyasi, S. Shahgaldi, S. Seddighi, M. M. Kasaei and L. F. M. da Silva, “The effect of rubber hardness on the channel depth of the metallic bipolar plates fabricated by rubber pad forming”, Adv. Struc. Mater. , Vol 168 pp. 123–133, (2023).
[39] H. Talebi-Ghadikolaee, V. Modanloo, M. Elyasi and F. A. Khatir, “Multiple criteria decision support analysis for manufacturing process parameters selection of metallic bipolar plates for polymer electrolyte membrane fuel cells”, Proc. Inst. Mech. Eng. Part L J. Mater. Des. Appl. , (2023).
[40] H. D. Azodi, A. Hassani, S. Mazdak and A. Zeinolabedin, “Numerical study on weld line displacement in rubber pad forming of tailor welded blanks”, J. Tech. Vocat. Univ. , Vol. 19, No. 1, pp. 145–164, (2022).
[41] H. Talebi-ghadikolaee, M. Elyasi and Y. D. Asl, “Feasibility of forming U-shaped microchannels by flexible-die forming process”, J. Tech. Vocat. Univ. , Vol. 19, No. 3, pp. 53–70, (2022).
[42] H.-C. Scheer, N. Bogdanski, M. Wissen, T. Konishi and Y. Hirai, “Polymer time constants during low temperature nanoimprint lithography”, J. Vac. Sci. Technol. B Microelectron. Nanom. Struct. Process. Meas. Phenom. , Vol. 23, No. 6, pp. 2963–2966, (2005).
[43] H. G. Nosrati and M. Gerdooei, “Experimental and numerical study of friction in free bulging 304 stainless steel seamed tube using elastic pad”, Modares Mech. Eng. , Vol. 15, No. 4, pp. 30–40, (2015).
[44] H. G. Nosrati, M. Gerdooei and M. Falahati Naghibi, “Experimental and numerical study on formability in tube bulging: A comparison between hydroforming and rubber pad forming”, Mater. Manuf. Process. , Vol. 32, No. 12, pp. 1353–1359, (2017).
[45] M. Ahmadpour and O. Ghahraei, “The impact of die corner radius and friction coefficient on bulge forming of T-shaped copper tubes using finite-element method and experimental analysis”, ADMT J. , Vol. 10, No. 1, pp. 31–38, (2017).
[46] E. Bagherpour, M. Reihanian, N. Pardis, R. Ebrahimi and T. Langdon, “Ten years of severe plastic deformation (SPD) in Iran, part I: equal-channel angular pressing (ECAP)”, Iran. J. Mater. Form. , Vol. 5, No. 1, pp. 71–113, (2018).
[47] F. Djavanroodi, A. A. Zolfaghari, M. Ebrahimi and K. M. Nikbin, “Equal channel angular pressing of tubular samples”, Acta Metall. Sin. (English Lett.) , Vol. 26, No. 5, pp. 574–580, (2013).
[48] F. Djavanroodi, A. A. Zolfaghari, M. Ebrahimi and K. Nikbin, “Route effect on equal channel angular pressing of copper tube”, Acta Metall. Sin. (English Lett.) , Vol. 27, No. 1, pp. 95–100, (2014).
[49] F. Djavanroodi, A. A. Zolfaghari and M. Ebrahimi, “Experimental investigation of three different tube equal channel angular pressing techniques”, Kov. Mater. , Vol. 53, No. 1, pp. 27–34, (2015).
[50] O. Shapourgan and G. Faraji, “Rubber pad tube straining as a new severe plastic deformation method for thin-walled cylindrical tubes”, Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. , Vol. 230, No. 10, pp. 1845–1854, (2016).
آمار
تعداد مشاهده مقاله: 543
تعداد دریافت فایل اصل مقاله: 257
