Investigating the effect of different anisotropic surface roughening methods on ionic polymer metal composites behavior

Mosaddeghi, A.; Soleimanimehr, H.; Alinia Ziazi, A.

doi:10.22061/jcarme.2023.9633.2292

تعداد نشریات	13
تعداد شماره‌ها	238
تعداد مقالات	2,418
تعداد مشاهده مقاله	3,962,362
تعداد دریافت فایل اصل مقاله	2,874,084

	Investigating the effect of different anisotropic surface roughening methods on ionic polymer metal composites behavior
Journal of Computational & Applied Research in Mechanical Engineering (JCARME)
مقاله 10، دوره 13، شماره 1 - شماره پیاپی 25، مهر 2023، صفحه 113-121 اصل مقاله (856.08 K)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22061/jcarme.2023.9633.2292
نویسندگان
A. Mosaddeghi؛ H. Soleimanimehr^* ؛ A. Alinia ziazi
Department of Mechanics, Electrical Power and Computer, Science and Research Branch, Islamic Azad University, Tehran, Iran
تاریخ دریافت: 23 بهمن 1401، تاریخ بازنگری: 10 خرداد 1402، تاریخ پذیرش: 12 تیر 1402
چکیده
As the smart materials, ionic polymer-metal composites (IPMCs), have a layered structure consisting of a polymeric membrane based on perfluorinated alkene, which is sandwiched between two noble metal-based electrodes, such as gold and platinum, and they can be bent significantly under applying a low-range of voltage. IPMCs are used in many applications, such as robotics, biomechanics, and medical purposes. In order to improve the performance of IPMC, in this article, three different anisotropic surface roughening methods with new and optimized fabrication instructions are used, and samples are compared. The experiments are applied to measure three main factors of IPMCs: displacement, blocking force, and lifetime. The results obtained from plasma samples show that the maximum displacement is 36.23 mm, the blocking force is 4.08 etching, 18 percent higher lifetime than micro sandblasting, and sandpaper under applying a voltage range between 1-7 V; as a result, the plasma etched IPMC sample has the most efficiency.
کلیدواژه‌ها
Membrane؛ Voltage؛ Plasma treatment؛ Displacement

مراجع
[1] D. Chen and P. Q., "Electronic muscles and skins: a review of soft sensors and actuators," Chem. Rev., pp. No. 117, p. 11239–11268, (2017). [2] B. Bhandari, G. Lee and S.-H. Ahn, "A review on IPMC material as actuators and sensors: fabrications, characteristics and applications.," Int. J. Precis. Eng. Manuf., No. 14, p. 141–163, (2012). [3] A. Filimon and A. Dobos, "Role of Metal Ion Implantation on Ionic Polymer Metal Composite Membranes. In: Inamuddin, Asiri A. (eds) Ionic Polymer Metal Composites for Sensors and Actuators," Engineering Materials. Springer, Cham, pp. 53-73, (2019). [4] Y. Bar-Cohen, "Electroactive Polymer (EAP)Actuators as Artificial Muscles:Reality, Potential, and Challenges," in SPIE Publications, (2007). [5] K. Asaka, K. Kim, K. Oguro and M. Shahinpoor, "IPMCs as EAPs: fundamentals," Electromech. Active Polym, Vol. 6, pp. 131-150, (2016). [6] L. Chang, H. Chen, Z. Zhu and B. Li, "Manufacturing process and electrode properties of palladium-electroded ionic polymer–metal composite," Smart Mater. Struct.,Vol. 21, No. 6, (2012). [7] O. Kim, S. Kim and M. Park, "Low-voltage-driven soft actuators," Chem. Commun, Vol. 54, p. 4895–4904, (2018). [8] S. Lee, Y. Choi, J. Y. Lee, T. Yang, J. Y. Jho, J.H. Park, " Improved ionic and mechanical properties of ion-exchange membrane with an ionic silica network for high-performance ionic polymer-metal composites, "Journal of Industrial and Engineering Chemistry, Volume 122, 25, Pages 79-89, (2023). [9] Y. Tang, Z. Xue, X. Zhou, X. Xie and C.-Y. Tang, "Novel sulfonated polysulfone ion exchange for ionic polymer–metal composite actuators.," Actuators, Vol. 202, p. 1164–1174, (2014). [10] A. Nasrollah, H. Soleimanimehr, H. Khzani, " Nafion-based ionic-polymer-metal composites: Displacement rate analysis by changing electrode properties" Advanced Journal of Science and Engineering, Vol. 2, No. 1, p . 51-58, (2021). [11] H. Qingsong, Y. Min, D. Haitao, G. Dongjie and D. Zhendong, "Effects of anisotropic surface texture on the performance of ionic polymer-metal composite (IPMC)," in SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring, San Diego, California, United States, (2010). [12] Y. Wang, Z. Zicai, L. Jiayu, C. Longfei and C. Hualing, "Effects of surface roughening of Nafion 117 on the mechanical and physicochemical properties of ionic polymer–metal composite (IPMC) actuators," Smart Mater. Struct. , Vol. 25, No. 8, (2016). [13] A. Nasrollah, H. Soleimanimehr, S. Javangoroh " Finite element analysis assisted improvement of ionic polymer metal composite efficiency for micropump of 3d bioprinter, " Advanced Journal of Science and Engineering, Vol. 2, No. 1, p . 23-30, (2021). [14] C. Zhang, C. Hualing, W. Yanjie, J. Shuhai, W. Yongquan and J. Shuhai, "Comparison of plasma treatment and sandblast preprocessing for IPMC actuator," in SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring, San Diego, California, United States, (2014). [15] A. Nasrollah, P. Farnia, S. Hamidgorgani, J. Ghanavi, " A novel experimental static deflection equation for specific cantilever beam made of ionic polymer–metal composite, ", Biomedical and Biotechnology Research Journal (BBRJ), Vol. 6, No. 3, p . 429, (2022). [16] K. Farinholt and D. J. Leo, "Modeling of electromechanical charge sensoring in ionic polymer transducers," Mech. Mater., Vol. 36, No. 5, p. 421–433, (2004). [17] M. Karimi and F. Mohammadi, "Deep eutectic solvent (DES)/O2 as an electrochemical indicator for acidic groups in the solid polymer electrolytes," Journal of Molecular Liquids, Elsevier, (2020). [18] Y. Liu, L. Chang, Y. HU, N. Qingzheng , Y. Linfeng , W. Yanjie , P. Lu and Y. Wu, "Rough interface in IPMC: modeling and its influence analysis," Smart Materials and Structures, Vol. 27, No. 7, (2018). [19] M. Hao, Y. Wang, Z. Zhu, Q. He, D. Zhu and M. Luo, "A Compact Review of IPMC as Soft Actuator and Sensor: Current Trends, Challenges, and Potential Solutions From Our Recent Work," Front. Robot. AI, (2019). [20] S. Jung, S. Ko, J. Park and S. Park, "Enhanced ionic polymer–metal composite actuator with pore size–controlled porous Nafion membrane using silica sol–gel process," Journal of Intelligent Material Systems and Structures, Vol. 28, No. 11, pp. 1514-1523, (2016). [21] K. Kim and M. Shainpoor, "Ionic polymer–metal composites: II Manufacturing techniques.," Smart Mater. Struct.,No. 12, p. 65–79, (2003). [22] S. Kim, I. Lee and Y. Kim, "Performance enhancement of IPMC actuator by plasma surface treatment," Smart Mater. Struct.,No. 16, pp. 6-11, (2007). [23] S. Saher, S. Moon, S. Kim, H. Kim and Y. Kim, "O2 plasma treatment for ionic polymer metal nano composite (IPMNC) actuator," Sensors and Actuators, pp. 170-179, (2010). [24] D. Guo, L. Wang, X. Wang, Y. Xiao, C. Wang, L. Chen and Y. Ding, "PEDOT coating enhanced electromechanical performances and prolonged stable working time of IPMC actuator," Sensors and Actuators B: Chemical, Vol. 305, (2020). [25] N.-J. Choi, H.-K. Lee, S. Jung, S. Lee and K.-H. Park, "Electroactive Polymer Actuator with High Response Speed Through Anisotropic Surface Roughening by Plasma Etching," Journal of Nanoscience and Nanotechnology, Vol. 8, p. 5385–5388, (2008). [26] S. Kilm, S. Kim, K. Kim and Y. Kim, "An electrode model for ionic polymer–metal composites.," Smart Mater. Struct.,Vol. 16, p. 2286–2295, (2007). [27] H. Soleimanimehr, A. Nasrollah, " A Numerical Investigation the Effects of the Voltage on the Displacement and Stress of Copper-based Ionic Polymer-Metal Composites " Journal of Modern Processes in Manufacturing and Production, Vol. 10, No. 1, pp. 77-86, (2021). [28] D. Gendron, "Conducting Polymer Based Ionic Polymer Metal Composite Actuators," in Ionic Polymer Metal Composites for Sensors and Actuators, Engineering Materials. Springer, Cham,(2019), pp. 35-52. [29] A. Dobos and A. Filimon, "Role of Metal Ion Implantation on Ionic Polymer Metal Composite Membranes," in Inamuddin, Asiri, A. (eds) Ionic Polymer Metal Composites for Sensors and Actuators, Engineering Materials. Springer, Cham, (2019), pp. 53-74. [30] H. Kim and N. Vinh, "Study on Time-Dependent Bending Response of IPMC Actuator," in Inamuddin, Asiri, A. (eds) Ionic Polymer Metal Composites for Sensors and Actuators, Engineering Materials. Springer, Cham, (2019), pp. 75-138.
آمار تعداد مشاهده مقاله: 515 تعداد دریافت فایل اصل مقاله: 527

سامانه مدیریت نشریات علمی. طراحی و پیاده سازی از سیناوب

پیوندهای مفید

آمار

Investigating the effect of different anisotropic surface roughening methods on ionic polymer metal composites behavior