Design and manufacture a novel tool in the incremental sheet metal forming process and its effects on the process parameters

Haghani, E.; Gheysarian, A.; Honarpisheh, M.

doi:10.22061/jcarme.2019.4430.1536

تعداد نشریات	11
تعداد شماره‌ها	228
تعداد مقالات	2,324
تعداد مشاهده مقاله	3,711,658
تعداد دریافت فایل اصل مقاله	2,721,072

	Design and manufacture a novel tool in the incremental sheet metal forming process and its effects on the process parameters
Journal of Computational & Applied Research in Mechanical Engineering (JCARME)
مقاله 2، دوره 9، شماره 1 - شماره پیاپی 17، مهر 2019، صفحه 19-31 اصل مقاله (1.11 M)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22061/jcarme.2019.4430.1536
نویسندگان
E. Haghani؛ A. Gheysarian؛ M. Honarpisheh^*
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
تاریخ دریافت: 03 آذر 1397، تاریخ بازنگری: 30 بهمن 1397، تاریخ پذیرش: 06 اسفند 1397
چکیده
One of the methods for making prototypes is incremental forming process. In this method, the forming tool, performs a pre-programmed movement by the CNC machine and runs the desired path. This modernization process is used in the automotive, aerospace, military, medical and other industries. One of the most influential parameters in this process is forming tool. This parameter is effective in forming forces, surface roughness, sheet formability and thickness distribution. In this study, the forming tool was investigated and rotating geometry tool was compared with a rigid tool. Also, the effects of step down, feed rate and spindle speed were investigated on the forming force, surface roughness and thickness distribution by comparing mentioned forming tools. The results indicate that the forming forces, sheet surface quality and thickness changes increase with increasing step down and feed rate. Using the rotary tools improves the forming forces, surface roughness and thickness distribution rather than the non-rotating tool.
کلیدواژه‌ها
Incremental forming؛ Rotary tool؛ Thickness variation؛ Forming force

مراجع
[1] Jeswiet, J., F. Micari, G. Hirt, A. Bramley, Joost Duflou, and J. Allwood. "Asymmetric single point incremental forming of sheet metal." CIRP Annals-Manufacturing Technology, Vol. 54, No. 2, pp. 88-114 (2005). [2] Jeswiet, J., E. Hagan, and A. Szekeres. "Forming parameters for incremental forming of aluminium alloy sheet metal." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 216, No.10, pp. 1367-1371(2002). [3] Silva, M. B., Pedro Teixeira, Ana Reis, and P. A. F. Martins. "On the formability of hole-flanging by incremental sheet forming." Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications, Vol. 227, No. 2, pp. 91-99 (2013). [4] Montanari, L., V. A. Cristino, M. B. Silva, and P. A. F. Martins. "On the relative performance of hole-flanging by incremental sheet forming and conventional press-working." Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications, Vol. 228, No. 4, pp. 312-322 (2014). [5] Ambrogio, G., L. Filice, and G. L. Manco. "Warm incremental forming of magnesium alloy AZ31." CIRP Annals-Manufacturing Technology, Vol. 57, No. 1 pp. 257-260 (2008). [6] Manco, G. L., and G. Ambrogio. "Influence of thickness on formability in 6082-T6." International Journal of Material Forming Vol. 3, No. 1 pp. 983-986 (2010). [7] Mirnia, M. J., B. Mollaei Dariani, H. Vanhove, and J. R. Duflou. "An investigation into thickness distribution in single point incremental forming using sequential limit analysis." International Journal of Material Forming, Vol. 7, No. 4, pp. 469-477 (2014). [8] Hagan, E., and J. Jeswiet. "Analysis of surface roughness for parts formed by computer numerical controlled incremental forming." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 218, No. 10, pp. 1307-1312 (2004). [9] Fratini, L., G. Ambrogio, R. Di Lorenzo, L. Filice, and F. Micari. "Influence of mechanical properties of the sheet material on formability in single point incremental forming." CIRP Annals-Manufacturing Technology, Vol. 53, No. 1 pp. 207-210 (2004). [10] Iseki, Hideo. "An approximate deformation analysis and FEM analysis for the incremental bulging of sheet metal using a spherical roller." Journal of Materials Processing Technology, Vol. 111, No. 1, pp. 150-154 (2001). [11] Iseki, Hideo, and Takashi Naganawa. "Vertical wall surface forming of rectangular shell using multistage incremental forming with spherical and cylindrical rollers." Journal of materials processing technology, Vol. 130, pp. 675-679 (2002). [12] Filice, L., L. Fratini, and F. Micari. "Analysis of material formability in incremental forming." CIRP annals-Manufacturing technology, Vol. 51, No. 1, pp. 199-202 (2002). [13] Attanasio, A., E. Ceretti, and C. Giardini. "Optimization of tool path in two points incremental forming." Journal of Materials Processing Technology, Vol. 177, No. 1, pp. 409-412 (2006). [14] Young, D., and J. Jeswiet. "Wall thickness variations in single-point incremental forming." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 218, No. 11, pp. 1453-1459 (2004). [15] Hussain, G., L. Gao, and Z. Y. Zhang. "Formability evaluation of a pure titanium sheet in the cold incremental forming process." The International Journal of Advanced Manufacturing Technology, Vol. 37, No. 9-10, pp. 920-926 (2008). [16] Hamilton, K., and J. Jeswiet. "Single point incremental forming at high feed rates and rotational speeds: Surface and structural consequences." CIRP Annals-Manufacturing Technology, Vol. 59, No. 1, pp. 311-314 (2010). [17] Kurra, Suresh, Srinivasaprakash Regalla, and Amit Kumar Gupta. "Parametric study and multi-objective optimization in single-point incremental forming of extra deep drawing steel sheets." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 230, No. 5, pp. 825-837 (2016). [18] Bao, Wenke, Xingrong Chu, Shuxia Lin, and Jun Gao. "Experimental investigation on formability and microstructure of AZ31B alloy in electropulse-assisted incremental forming." Materials & Design, Vol. 87, pp. 632-639, (2015). [19] Suresh, Kurra, and Srinivasa Prakash Regalla. "Analysis of formability in single point incremental forming using finite element simulations." Procedia Materials Science, Vol. 6, pp. 430-435, (2014). [20] Senthil, R., and A. Gnanavelbabu. "Numerical analysis on formability of AZ61A magnesium alloy by incremental forming." Procedia Engineering, Vol. 97, pp. 1975-1982 (2014). [21] Mugendiran, V., and A. Gnanavelbabu. "Comparison of FLD and thickness distribution on AA5052 aluminium alloy formed parts by incremental forming process." Procedia Engineering, Vol. 97 pp. 1983-1990 (2014). [22] McAnulty, Tegan, Jack Jeswiet, and Matthew Doolan. "Formability in single point incremental forming: A comparative analysis of the state of the art.", CIRP Journal of Manufacturing Science and Technology, Vol. 16, pp. 43-54 (2017). [23] EH. Uheida, G. A. Oosthuizen, and D. Dimitrov, "Investigating the Impact of Tool Velocity on the Process Conditions in Incremental Forming of Titanium Sheets", Procedia Manufacturing Vol. 7, pp. 345-350 (2016). [24] D. Afonso, R. Alves de Sousa, and R. Torcato, "Incremental Forming of Tunnel Type Parts", Procedia Engineering, Vol. 183, pp. 137-142, (2017). [25] MR. Sakhtemanian, M. Honarpisheh, and S. Amini, "Numerical and experimental study on the layer arrangement in the incremental forming process of explosive-welded low-carbon steel/CP-titanium bimetal sheet", The International Journal of Advanced Manufacturing Technology, Vol. 95, No. 9, pp. 3781-3796, (2018). [26] M. Honarpisheh, and A. Gheysarian, "An Experimental Study on the process parameters of Incremental Forming of Explosively-Welded Al/Cu Bimetals", Journal of Computational & Applied Research in Mechanical Engineering, Vol. 7, No. 1, pp. 73-83, (2017). [27] M. Honarpisheh, M. Mohammadi Jobedar, and I. Alinaghian, "Multi-response optimization on single-point incremental forming of hyperbolic shape Al-1050/Cu bimetal using response surface methodology", The International Journal of Advanced Manufacturing Technology, Vol. 96, No. 9-12, pp.3069-3080, (2018). [28] M. Honarpisheh, M. Keimasi, and I. Alinaghian, “Numerical and experimental study on incremental forming process of Al/Cu bimetals: influence of process parameters on the forming force, dimensional accuracy and thickness variations", Journal of Mechanics of Materials and Structures Vol. 13, pp. 35-51, (2018). [29] M. Honarpisheh, M. J. Abdolhoseini, and S. Amini, "Experimental and numerical investigation of the hot incremental forming of Ti-6Al-4V sheet using electrical current", The International Journal of Advanced Manufacturing Technology, Vol. 83, No. 9-12 pp. 2027-2037, (2016). [30] A. Gheysarian, and M. Honarpisheh, "Process Parameters Optimization of the Explosive-Welded Al/Cu Bimetal in the Incremental Sheet Metal Forming Process." Iranian Journal of Science and Technology, Transactions of Mechanical Engineering: pp. 1-12, (2018). [31] Sakhtemanian, M. R., M. Honarpisheh, and S. Amini. "A novel material modeling technique in the single-point incremental forming assisted by the ultrasonic vibration of low carbon steel/commercially pure titanium bimetal sheet." The International Journal of Advanced Manufacturing Technology, 1-14, (2019). [32] Sakhtemanian, M. R., S. Amini, and M. Honarpisheh. "Simulation and investigation of mechanical and geometrical properties of St/CP-titanium bimetal sheet during the single point incremental forming process." Iranian Journal of Materials Forming 5, no. 1, 1-18, (2018).
آمار تعداد مشاهده مقاله: 1,890 تعداد دریافت فایل اصل مقاله: 1,555

سامانه مدیریت نشریات علمی. طراحی و پیاده سازی از سیناوب

پیوندهای مفید

آمار

Design and manufacture a novel tool in the incremental sheet metal forming process and its effects on the process parameters